TOMEI POWERED INC. ONLINE CATALOGUE

カムシャフト SR20DE

カムシャフト

PRODUCT INFO



タイプ 適合 作用角(°) リフト量(mm) IN/EX 品番 定価
エンジン 車種 IN EX IN EX
N SR20DE P10,W10 260 260 11.20 11.20 1台分セット 143041 ¥44,000 (税込 ¥48,400)
P11 143039
(R)PS13 143040
S14,S15 143042

※バルブスプリング交換不要
※バルタイ調整不要




適合 タイプ 作用角(°) リフト量(mm) IN/EX 品番 定価 備考
SR20DE ラッシュ 260 11.20 IN (R)PS13,P10,W10 143E260112 ¥22,000 (税込 ¥24,200) PONCAM同一品
S14,S15(NVCS対応) 143H260112
EX P10,W10 143J260112
(R)PS13,S14,S15 1439260112
12.00 IN (R)PS13,P10,W10 1431260120
S14,S15(NVCS対応) 143H260120
EX P10,W10 143J260120
(R)PS13,S14,S15 1432260120
270 12.50 IN (R)PS13,P10,W10 1431270125
EX P10,W10 143J270125
(R)PS13,S14,S15 1432270125
ソリッド 260 12.00 IN (R)PS13,P10,W10 1435260120 ¥22,000 (税込 ¥24,200)
EX P10,W10 143K260120
(R)PS13,S14,S15 1436260120
270 12.50 IN (R)PS13,P10,W10 1435270125
EX P10,W10 143K270125
(R)PS13,S14,S15 1436270125
280 12.50 IN (R)PS13,P10,W10 1435280125
EX P10,W10 143K280125
(R)PS13,S14,S15 1436280125

※ソリッドタイプには別途、ソリッドピボットとアジャストシムおよび、ガイドが必要です。

FEATURE / SPEC

■ SPEC
ENGINE タイプType 作用角(°)Duration 最大カムリフト量(mm)Max Cam lift (mm) IN/EX 最大バルブリフト量(mm)Max Valve lift (mm) 冷間時バルブクリアランス
(mm) [±0.01]
Cold Valve Clearance
(mm)[±0.01]
バルタイ初期設定
中心角(度)
Valve Timing Centerline
(Deg)
ベース円Base circle 備考Note
SR20DE ラッシュLash 260 7.23 IN 11.20 110 32 PONCAM
130 PONCAM(NVCS)
EX 115 PONCAM
7.70 IN 12.00 110
130 NVCS
EX 115
270 8.00 IN 12.50 110
130 NVCS
EX 115
ソリッドSolid 260 7.88 IN 12.00 0.15 110 32
130 NVCS
EX 115
270 8.17 IN 12.50 110
130 NVCS
EX 115
280 8.17 IN 12.50 110
130 NVCS
EX 115
TOMEIカムシャフトシリーズの特徴Theme of TOMEI CAMSHAFT

吸排気非対称GコントロールプロフィールAsymmetrical G-Controlled Profile

カムがバルブを開く時は、短時間で大量の混合気を有効に吸入できるため、高い加速度(G)1が求められます。
しかし逆に、バルブを閉じる時は加速度(G)が高いとバルブシートへの衝撃やバルブスプリングへの負担が大きくなるため、加速度(G)を低くしてバルブを静かに着座させる必要があります。
そこで吸排気のプロフィールを非対象にして、加速度を適正な値にコントロールすることで、シートへの衝撃やスプリングへの負担を著しく低減させ、回転余裕と動弁系の信頼性向上を果たしました。
この吸排気非対象Gコントロールプロフィールは“大きな作用角とハイリフトを確保しつつもバルブシステムに負担をかけない”という相反した要求性能を現実のものとしました。
When opening the intake valve during high acceleration the G from the camshaft requires to send as much mixture to the cylinder in the shortest time possible. However if the speed is too high it can damaged the Valves, Valve Seats and Valve Springs if the Acceleration G is too high. The Asymmetrical profile design given to the camshafts will allow the Intake and Exhaust Valves to fulfill the target requirement with the wider duration and high lift without damaging the Valve System.

有効バルブ面積の確保Maximizing the Valves Efficiency



エンジンチューニングとは、一般的にカム作用角とリフト量を変更してエンジンのトルク特性を操作することで、最大トルクを上げたり、発生点を高回転側にして最高エンジン出力を上げることです。
しかし、厳密にエンジンチューニングする場合は単に作用角とリフト量の数値だけではなく、徹底的に吸気効率を追求して有効なバルブ面積を確保するという考え方で取り組むべきです。
バルブリフトが高いと、空気の流路は大きく開かれ、大量の空気を吸い込むことができます。しかし、大きなバルブリフトはバルブシステムに負担をかけ、高回転の妨げとフリクションの増大を招きます。
また、大きなカム開度(作用角)は大きなバルブオーバーラップから生まれる慣性吸気効果により高回転でエンジン出力を引き出すことができますが、低回転での運転性悪化につながります。したがって必要かつ十分な作用角で、可能な限りハイリフトを確保し、大量の空気を吸い込む必要があります。
吸気効率を追求したこの設計思想を取り入れたTOMEIカムは、ノーマルを100%としたとき、実に130~150%の有効バルブ面積を確保しています。

The general purpose of engine tuning is to change the torque characteristics of the engine by changing the cams duration timing and cam lift amount for maximum torque and horse power. However tuning the engine is not only based on that. When going into finer details by maximizing the Valves efficiency is not just about timing and height lift but to also maximize the intake efficiency. The high valve lift allows huge amounts of air in but at the same time it mechanically damages the valve train and gains added friction loss. Longer cam durations and big cam lifts give deliver more power at higher engine speeds but it also gives a rough idle and at low engine speeds. Tomei engineers worked hard to produce camshafts that will deliver a well balanced profile at 1.3-1.5 times more than the stock camshaft.

徹底した生産品質管理Quality Control

これらの幾多にも渡る生産工程を経て1本1本丁寧に生産されます。お客様には、厳しい検査をクリアした最高品質の商品だけが出荷されます。
Every camshaft is carefully built through these production processes. Plus, strict inspection will be given to them and only the highest quality products are shipped.

表面処理の実施Surface Coating


エンジンオイルがまだ潤滑していない状態の時でも、摺動表面を保護する目的で、ローラーロッカータイプ以外のカムシャフトの表面にリン酸マンガン皮膜処理(リューブライト処理)を施します。 これは浸漬法によりカム山表面に厚さ0.5~15ミクロンの薄いリン酸マンガン系の不動態皮膜を生成し、金属同士の直接接触を防止することで高い摺動性を確保して滑らかなカムの動きを実現します。 Coating the surface of camshaft with manganese phosphate in order to protect from damage even when the camshaft has not lubricated yet. This has done by steeping press process that produces 0.5mm to 15 micromillimeter thin of manganese phosphate coating on its surface to prevent from direct contact with other metal parts while realizing smooth operation.

CNCカム研削盤による超高精度、高速研削CNC Super Precise High Speed Grinding



超高速主軸とダイヤモンド砥石の組み合わせをコンピュータで制御。自動車メーカーと同一の専用機を用いることで、作業時間を300%向上しながらも高精度研削を実現。驚異のプロフィール精度と価格を実現しましています。 The combination of a ultra high-speed main bearing and diamond grindstone is controlled by the computer. By using the same special-purpose machine as an automaker, high precision grinding is realized though in 1/3 period of time. Consequently, incredible accuracy of profile and remarkable price were realized at the same time.

オシレーション研削による波目付仕上げWavy Groove Finish by Oscillation Grinding

カム研削時のオシレーションにより、カム山表面に波目をつけます。これにより、カム山表面にはオイル溜まりが形成され、フリクションロスを低減させ、かじりを防止します。 Wavy groove is curved to the cam profile surface by oscillation during cam grinding process. Oil pool that is formed on the cam profile surface reduces a friction loss and prevents locking.


PONCAMとはAbout “PONCAM”


PROCAMとはAbout “PROCAM”


標準車カムシャフト諸元表Factory Camshaft specs


エンジンEngine 車種Model タイプType カム作用角/IN (°)Cam Duration/IN (°) カム作用角/EX (°)Cam Duration/EX (°) カムリフト/IN (mm)Cam lift/IN (mm) カムリフト/EX (mm)Cam lift/EX (mm) 中心角/IN (°)Pre-Set Valve Timing/IN (°) 中心角/EX (°)Pre-Set Valve Timing/EX (°) NVCS NVCSレンジ(rpm)NVCS range(rpm)
SR20DE PS13 ラッシュLash 248 246 10.00 9.20 117 120 None
S14 240 130 113 1050~8000
S15
P10 115 111 None
P11 240 232 9.40 8.50 118 109 None

関連製品RELATED PRODUCT

SR20 ソリッドピボット / テストガイド・テストシムSOLID PIVOT / TEST SHIM & TEST GUIDE for SR20

CAMSHAFT SR20DE

CAMSHAFT

PRODUCT INFO



TYPE APPLICATION DURATION(°) MAX CAM LIFT(mm) IN/EX P/N JPY
ENGINE MODEL IN EX IN EX
N SR20DE P10,W10 260 260 11.20 11.20 IN & EX Set 143041 ¥44,000
P11 143039
(R)PS13 143040
S14,S15 143042

※PRESET VALVE TIMING
※STOCK VALVE SPRING COMPATIBLE




APPLICATION TYPE DURATION(°) Max Valve lift IN/EX P/N JPY NOTE
SR20DE Lash 260 11.20 IN (R)PS13,P10,W10 143E260112 ¥22,000 PONCAM
S14,S15(NVCS対応) 143H260112
EX P10,W10 143J260112
(R)PS13,S14,S15 1439260112
12.00 IN (R)PS13,P10,W10 1431260120
S14,S15(NVCS対応) 143H260120
EX P10,W10 143J260120
(R)PS13,S14,S15 1432260120
270 12.50 IN (R)PS13,P10,W10 1431270125
EX P10,W10 143J270125
(R)PS13,S14,S15 1432270125
Solid 260 12.00 IN (R)PS13,P10,W10 1435260120 ¥22,000
EX P10,W10 143K260120
(R)PS13,S14,S15 1436260120
270 12.50 IN (R)PS13,P10,W10 1435270125
EX P10,W10 143K270125
(R)PS13,S14,S15 1436270125
280 12.50 IN (R)PS13,P10,W10 1435280125
EX P10,W10 143K280125
(R)PS13,S14,S15 1436280125

※Solid Pivots, Adjust Shims and valve springs are needed for Solid type.

FEATURE / SPEC

■ SPEC
ENGINE タイプType 作用角(°)Duration 最大カムリフト量(mm)Max Cam lift (mm) IN/EX 最大バルブリフト量(mm)Max Valve lift (mm) 冷間時バルブクリアランス
(mm) [±0.01]
Cold Valve Clearance
(mm)[±0.01]
バルタイ初期設定
中心角(度)
Valve Timing Centerline
(Deg)
ベース円Base circle 備考Note
SR20DE ラッシュLash 260 7.23 IN 11.20 110 32 PONCAM
130 PONCAM(NVCS)
EX 115 PONCAM
7.70 IN 12.00 110
130 NVCS
EX 115
270 8.00 IN 12.50 110
130 NVCS
EX 115
ソリッドSolid 260 7.88 IN 12.00 0.15 110 32
130 NVCS
EX 115
270 8.17 IN 12.50 110
130 NVCS
EX 115
280 8.17 IN 12.50 110
130 NVCS
EX 115
TOMEIカムシャフトシリーズの特徴Theme of TOMEI CAMSHAFT

吸排気非対称GコントロールプロフィールAsymmetrical G-Controlled Profile

カムがバルブを開く時は、短時間で大量の混合気を有効に吸入できるため、高い加速度(G)1が求められます。
しかし逆に、バルブを閉じる時は加速度(G)が高いとバルブシートへの衝撃やバルブスプリングへの負担が大きくなるため、加速度(G)を低くしてバルブを静かに着座させる必要があります。
そこで吸排気のプロフィールを非対象にして、加速度を適正な値にコントロールすることで、シートへの衝撃やスプリングへの負担を著しく低減させ、回転余裕と動弁系の信頼性向上を果たしました。
この吸排気非対象Gコントロールプロフィールは“大きな作用角とハイリフトを確保しつつもバルブシステムに負担をかけない”という相反した要求性能を現実のものとしました。
When opening the intake valve during high acceleration the G from the camshaft requires to send as much mixture to the cylinder in the shortest time possible. However if the speed is too high it can damaged the Valves, Valve Seats and Valve Springs if the Acceleration G is too high. The Asymmetrical profile design given to the camshafts will allow the Intake and Exhaust Valves to fulfill the target requirement with the wider duration and high lift without damaging the Valve System.

有効バルブ面積の確保Maximizing the Valves Efficiency



エンジンチューニングとは、一般的にカム作用角とリフト量を変更してエンジンのトルク特性を操作することで、最大トルクを上げたり、発生点を高回転側にして最高エンジン出力を上げることです。
しかし、厳密にエンジンチューニングする場合は単に作用角とリフト量の数値だけではなく、徹底的に吸気効率を追求して有効なバルブ面積を確保するという考え方で取り組むべきです。
バルブリフトが高いと、空気の流路は大きく開かれ、大量の空気を吸い込むことができます。しかし、大きなバルブリフトはバルブシステムに負担をかけ、高回転の妨げとフリクションの増大を招きます。
また、大きなカム開度(作用角)は大きなバルブオーバーラップから生まれる慣性吸気効果により高回転でエンジン出力を引き出すことができますが、低回転での運転性悪化につながります。したがって必要かつ十分な作用角で、可能な限りハイリフトを確保し、大量の空気を吸い込む必要があります。
吸気効率を追求したこの設計思想を取り入れたTOMEIカムは、ノーマルを100%としたとき、実に130~150%の有効バルブ面積を確保しています。

The general purpose of engine tuning is to change the torque characteristics of the engine by changing the cams duration timing and cam lift amount for maximum torque and horse power. However tuning the engine is not only based on that. When going into finer details by maximizing the Valves efficiency is not just about timing and height lift but to also maximize the intake efficiency. The high valve lift allows huge amounts of air in but at the same time it mechanically damages the valve train and gains added friction loss. Longer cam durations and big cam lifts give deliver more power at higher engine speeds but it also gives a rough idle and at low engine speeds. Tomei engineers worked hard to produce camshafts that will deliver a well balanced profile at 1.3-1.5 times more than the stock camshaft.

徹底した生産品質管理Quality Control

これらの幾多にも渡る生産工程を経て1本1本丁寧に生産されます。お客様には、厳しい検査をクリアした最高品質の商品だけが出荷されます。
Every camshaft is carefully built through these production processes. Plus, strict inspection will be given to them and only the highest quality products are shipped.

表面処理の実施Surface Coating


エンジンオイルがまだ潤滑していない状態の時でも、摺動表面を保護する目的で、ローラーロッカータイプ以外のカムシャフトの表面にリン酸マンガン皮膜処理(リューブライト処理)を施します。 これは浸漬法によりカム山表面に厚さ0.5~15ミクロンの薄いリン酸マンガン系の不動態皮膜を生成し、金属同士の直接接触を防止することで高い摺動性を確保して滑らかなカムの動きを実現します。 Coating the surface of camshaft with manganese phosphate in order to protect from damage even when the camshaft has not lubricated yet. This has done by steeping press process that produces 0.5mm to 15 micromillimeter thin of manganese phosphate coating on its surface to prevent from direct contact with other metal parts while realizing smooth operation.

CNCカム研削盤による超高精度、高速研削CNC Super Precise High Speed Grinding



超高速主軸とダイヤモンド砥石の組み合わせをコンピュータで制御。自動車メーカーと同一の専用機を用いることで、作業時間を300%向上しながらも高精度研削を実現。驚異のプロフィール精度と価格を実現しましています。 The combination of a ultra high-speed main bearing and diamond grindstone is controlled by the computer. By using the same special-purpose machine as an automaker, high precision grinding is realized though in 1/3 period of time. Consequently, incredible accuracy of profile and remarkable price were realized at the same time.

オシレーション研削による波目付仕上げWavy Groove Finish by Oscillation Grinding

カム研削時のオシレーションにより、カム山表面に波目をつけます。これにより、カム山表面にはオイル溜まりが形成され、フリクションロスを低減させ、かじりを防止します。 Wavy groove is curved to the cam profile surface by oscillation during cam grinding process. Oil pool that is formed on the cam profile surface reduces a friction loss and prevents locking.


PONCAMとはAbout “PONCAM”


PROCAMとはAbout “PROCAM”


標準車カムシャフト諸元表Factory Camshaft specs


エンジンEngine 車種Model タイプType カム作用角/IN (°)Cam Duration/IN (°) カム作用角/EX (°)Cam Duration/EX (°) カムリフト/IN (mm)Cam lift/IN (mm) カムリフト/EX (mm)Cam lift/EX (mm) 中心角/IN (°)Pre-Set Valve Timing/IN (°) 中心角/EX (°)Pre-Set Valve Timing/EX (°) NVCS NVCSレンジ(rpm)NVCS range(rpm)
SR20DE PS13 ラッシュLash 248 246 10.00 9.20 117 120 None
S14 240 130 113 1050~8000
S15
P10 115 111 None
P11 240 232 9.40 8.50 118 109 None

関連製品RELATED PRODUCT

SR20 ソリッドピボット / テストガイド・テストシムSOLID PIVOT / TEST SHIM & TEST GUIDE for SR20
PAGE TOP